Activity
I put a thermometer on the ESC heatsink. I rode fast for a while under the sun (30ºC) and the thermometer came to show the maximum I noticed was 77ºC
77-80ºC in heatsink its safe?
i hope, for a castle mambas ESC it’s not good, this ESC not for Savage, not for 6S, at the limit of.
just touch it by hand, must be the same or you can use this hobbyking.com/…/turnigy-infrared-thermometer-33-18…
i use 8S 280А ESC for savage, ride on 6S-7Si can’t give you answer, i don’t know how all work with gearbox, maybe 25 is ok. just check temperature motor/esc
stock is good i think. look my faq
Thanks!!
You’re right, use other connectors, such as XT90.
DEANS is bad connector, have that problem without overheating. They have poor contact, in consequence of that they start to heats up, and the connection gets worse.
you have gearbox, and I don’t think 25t pinion affects somehow, besides you use 5S li-po.
Also, when using large wheels you get an increase in the load, and for the stock ESC would be better to change the pinion. Сheck your ESC temperature if it is higher than the motor. They should be approximately equal.
But im using 6S… still ok?
“Also, when using large wheels you get an increase in the load, and for the stock ESC would be better to change the pinion”
Change to 20t? 22t?
I have not the slightest idea of how to see the temperature of the ESC 😵
Hi. I’m using in my savage with gearing (44/25) and battery 2x3S
I have two wheel pair… an ON-ROAD wheel and another OFF-ROAD (Trencher)
I’m having a problem, it is the third time my DEANS connector melts a bit and lose the connection. This is just using the OFF-ROAD Trencher proline. With on-road tires have no problem.
Changing to bullet connector solve this problem? Or 44/25 is to high for esc and heats up? burn my esc with trencher tires?
Здравствуй. Я использую в моей дикаря с зубчатых зацеплений (44/25) и 2x3S батареи
У меня есть два колеса пару … в колесо на дороге и другую Внедорожный (Траншеекопатель)
У меня возникли проблемы, это третий раз, когда мой разъем DEANS тает немного, и терять связь. Это просто использует внедорожного Траншеекопатель пролина. С дорожных шин нет никаких проблем.
Изменение к разъему пули решить эту проблему? Или 44/25 является высокой для ЭСК и нагревается? сжечь мой с траншеекопатель ESC шин?
THANKS!!!
Мой сервопривод может правильно повернуть с силой, когда сервопривод тянет боковую сторону, но, когда он тянет на сторону B, он имеет меньшую прочность и во время езды он повернуть меньше. Как это исправить?
Я использую TURNIGY TS-900
Thiagoo, You are in on the Russian forum, where very few people with knowledge of English, if you wish something to ask - take the trouble to use the a translator order to somebody thee realized. To translate your matter is not who do not wants.
Sorry, i forget. But this is the only fully active forum as found to talk about the savage …
My servo can turn correctly with power when the servo pulls the A side, but when he pulls the B side, it has less strength and during the ride he turn less. How to fix this?
Im using turnigy ts-900
think it similar, i used only Telebee, its working well.
thanks!
Good day. My heatsink this taking off the ESC, already tried to fix a time but by the way, I checked today and it seems that this loose again.
Anyone know a way of fixing this? Some glue? Or something to derstand / fix
?
THANKS!!!
Hi. What type of lubricant / grease should I put here?
Already used white nautical grease but comes off easily
I do not think that is much cheaper than Alza, my CD mount. is not for stock TVP - it’s may cheaper. it’s expensive, but much expensive every time buy new 9t and lose time to replace.
пойдет.
To use your CD, also need to use your TVP?
When my country improve the economy maybe I buy. Today paid 4x the price in dollar / euro and am still taxed at 80%. Im live in Brazil. Congratulations for the work.
hmmm ok, but, whats gearing its safe? 44/20? problem is that with 20/44 gets much torque
ah… have a project for central differential? I thought only the alza-racing which costs a fortune!
Its not safe for you ESC.
no matter what the configuration of your Savage, the problem and solution of gear 9t is well-known, they can break on the flat road. use CD or HSF299X, both better.
Without CD i broke two HSF299 (28t), now available HSF299X stronger.
hmmm ok, but, whats gearing its safe? 44/20? problem is that with 20/44 gets much torque
Thanks, but, im already buy this
I hope it does not break again.
What does the center differential?
Too bad their installation is very expensive …
Ah… Im using 44/25pinion with this tires, its a safe gearing?
Hello! Use central diff, stock 9t will be safe.
Much better if you buy HSF299X (28/8t).
Read our FAQ (use google translate)
Bad landing with an opened throttle is a most common reason. If you are going to run 6s convert your diff with a helical gears from Hot Racing with a proper shimming you’ll forget about this issue.
Thanks, but, im already buy this
I hope it does not break again.
What does the center differential?
Too bad their installation is very expensive …
Good day.
I recently spent using 5s TO USE 6S…
In the first five minutes of walking 6S, running in the clay… here’s the problem:
Rear diff pinion broken
What are the reasons for this to happen? I already have this savage almost three years, could have been wear? Always running 4S / 5S.
I already bought a new piece, what precautions should I take? Thank you.
This is work on savage with a turnigy ts900 servo?
hobbyking.com/…/__10113__Hobby_King_401B_AVCS_Digi…
When did it happen?
When what happened?
The wheel makes it to one month
check the wheel axle, remove the wheel and pull the trigger
I tested this wheel on all axles, and this occurs in all of them …
and max RPM?
At maximum, maximum speed, everything seems to stop …
But to a certain high speed it remains very wobble.
This is clearly visible with the wheels in the air. With the wheels on the ground does not feel much.
See…
www.youtube.com/watch?v=cUZ-2sN3wNQ
Should look at the drive wheel
He also wags?
I’m thinking that the wheel may be pie … :/
What is this? unbalanced wheel? I tried to balance, put enough mass but to no avail … need to lead?
Or the problem is other thing???
лучше потом переделать, чем вообще не сделать.
Take off the satellite with the large gear and put it on the other satellites in the housing.
Rear panel of the satellite, where the slot for the pin, must lie in one plane with the housing border, no deeper.
Now, i can’t make photo of broken satellites, maybe after weekend, i try show what i mean.
You sure what decided that problem sites.google.com/…/vyskakivaet-kolesnaa-kost
Additionally you can limit the maximum steering angle, on you transmitter.он уже делал, правда только одну сторону, тут его фото sites.google.com/…/vyskakivaet-kolesnaa-kost
к тому же он едет назад, передняя подвеска проседает и кость заходит глубже в чашки.
ну ты ж у нас в инглише шаришь, я только на ВЫ и с переводчиком 😃) но попробую:
Thiagoo
One hand hold the machine with per the front bumper, the second hand to hold the remote control at the same time giving a little speed reverse gear and turn the steering wheel to the maximum so that it was visible the bone does not jump out of the cup a little bit, even at 1mm. Similarly the second check wheel. Bones should sit in a cup deep and protrusions should not go out of the slots cups! Wheels on the ground have to slide, so it’s better to do it on the sand.
Hei
Today I went to look at this problem again.
I discovered that this noise really is because of this:
imagizer.imageshack.us/v2/…/SSLLQc.jpg
When giving RESERVE and TURF LEFT, makes noise and sometimes locks the wheel.
I put a piece of FOAM in DIFF CUP… but no way, has slack, I have to arrange something more efficient.
не слушай… пока будешь паять еще че нибудь сломаешь, как этот rcopen.com/forum/f27/topic123165/18868
купи смолы пожиже, и залей в кирпич в родном боксе, не забудь кнопку вкл/выкл убрать (спаять два контакта или проводка)
вариант проще некуда, быстро и надежно, все равно если че сгорит ремонт не целесообразен и не надолго, не забудь внешний бэк, без него лучше вообще не катай (хоть самый дешевый).Can i use your video in my faq?
sites.google.com/site/…/strannyj-tresk-sesternej
i know the problem that you have in that video.
Front diff, check satellites inside it. (please answer here, after checking, i’m right or not?)
Do you use Plastic gear housing? Often meets with plastic housing.
Some housing litle longer/deeper, use washer under satellite (if it’s posible) #86972 - WASHER 6X15X0.2MM
Grind/cut housing how much needed (if you can).
Raplase diff housing (if you can’t anything)
Yes, you can use my video!
My housing diff is Metal.
Doesnt have any broken satellite.
What I have to do? remove slack from satellites?
what do you mean by this image of the faq?
check drive bone in the steering axle
I’m very happy with this forum, you are people that help me a lot. Difficult to find another forum as well. Thank Russians.
when going back and steer the wheel, the bone comes out of the axis
плохого не сделают, но зацеп у них только по траве и крупному грунту хорош
check drive bone in the steering axle
Will be?
I ordered the axles savage xl, hope that solves!
This problem keeps!
www.youtube.com/watch?v=_fiHCQ9eaew
- I checked the two differentials, none of them present problems, and are now with oil silicone30k
- The transmission is also OK!
- The cup-joint diff and wheel are ok too …
anyone have any suggestions?
Thanks for second Photo.
just translate it) sites.google.com/…/vyskakivaet-kolesnaa-kostв расширении колесной базы
Hi, this thing decide yours second question
HPI-75080 O-RING 7x11x2.0mm (BLACK/8pcs)
Take Dremel, and make transverse incisions on the motor shaft (if there is no Dremel, skip this), the shaft smear blue threadlock and place the pinion, smear thread of pinion blue threadlock, tighten the new screw, wait for drying.
You can remove that only with heating burner
Thanks 😁😁😁😆
Hi, can you help me on two things?
First: is the third time that the engine sprocket gives off! I squeeze it and put lock thread but no use, I put the last pinion is new!
Second: The dogbone is eating the axle of the wheel. Does the control setup is doing a lot of curve? What can I do?
Anyone know why this noise is happening to give into reverse?
the transmission gears are OK
Каждый знает, почему это происходит шум, чтобы дать задний ход?
шестерни передачи в порядке
Good morning, how are you doing with the hex?
I had a set of these, HK, until yesterday …
hobbyking.com/hobbyking/store/uh_viewItem.asp?idPr…
But yesterday there were problems, came off the wheel. Along with the HEX and I lost the nut. But, as I use 2 pins, he destroyed the plastic around, I think it turned together.
Look:
Have a suggestion hex that works well? Without sanding to fit properly?
Damage from the weekend:
Jumped 1.5 m high and fell with one wheel
But I managed to straighten out, but bought one new pair
I have a question … where I buy it? Have for drivecups wheels too?
У меня есть вопрос … где купить? У чашки для ведущих колес?
>>>>
Thanks!
What do I do to remove it?
This dusted, there’s no way out!
Turnigy 120a hobbyking.com/…/__22632__Turnigy_TrackStar_120A_Br…
skyrc Toro esc? its the same as turnigy tracstar??
item.mobileweb.ebay.com/viewitem?itemId=2610337342…
Ezrun 120a rcecho.com/HOBBYWING-EZRUN-WP-SC8-Waterproof-120A-…
Hobbyking 120a
hobbyking.com/…/__17233__HobbyKing_100A_Sensored_S…
Which one to choose? or have any other option better? thank you!
It’s looked like the problem in one phase, maybe in ESC, maybe cable between ESC and motor , maybe in motor. better if you find other motor or ESC and try to run.
Yes, you should. You need to find broken canal.
Ok but how do I know if the cable is faulty or working? Another fact is that this esc no more whistling!
I sent email support pro hpi and got this message:
Hi Thiago,
Thank you for contacting HPI Racing and HB. It sounds like there is an issue with the ESC. Can you tell me the brand, C rating, and other specifications of the battery you are using?
Regards,
Victoria Reynolds
However, watching these videos, it really looks like a engine problem
😵😵😵😵😵😵😵
I squeezed a little on the cables and now look just … the problem continues, but sometimes it runs … and without stopping!
www.youtube.com/watch?&v=uQRhPzlIDQ4
Попытаюсь на словах:
Имеем 3 провода и где-то нет фазы, а также дергающийся мотор.
Следовательно, разъединяя поочередно каждый провод, мы найдем где нет фазы (один будет разъединен и мотор будет, также как и на трех, дергаться на двух проводах). Затем, из 2х оставшихся проводов выбираем любой и переставляем в свободный разъем на регуле.
Если мотор молчит - фазы нет на регуле. Если все также дергается - проблема с мотором.
Sorry, I do not understand Russian, but I need the help so I came to this forum is one of the best.
google translator could understand something.
Should I remove a cable? let alone two?
I’ll try something. Thank you.
Хана мотору.
The problem in the motor.
I sent email support pro hpi and got this message:
Hi Thiago,
Thank you for contacting HPI Racing and HB. It sounds like there is an issue with the ESC. Can you tell me the brand, C rating, and other specifications of the battery you are using?
Regards,
Victoria Reynolds
However, watching these videos, it really looks like a engine problem
😵😵😵😵😵😵😵
mossavage wrote to you before -
Check the contacts on the ESC to motor.
I had the same problem. Had a poor contact on the ESC wires to the motor.
The cable plugs A, B, C?
I checked … I looked at them, I seem to be okay.
What I have to do?
I took a savage to run today and see what happens:
When connecting the battery there is a strange beep. When I press the trigger the car moves very little and makes a strange noise.
www.youtube.com/watch?v=4DRut7ctb_Y
I can fix this or do I have to send the warranty?
:/
Help me. This problem is in ENGINE or ESC?
ESC? Motor?
Помогите мне. Эта проблема в двигателе или ESC?
I took a savage to run today and see what happens:
When connecting the battery there is a strange beep. When I press the trigger the car moves very little and makes a strange noise.
www.youtube.com/watch?v=4DRut7ctb_Y
what problem is this?
ESC? Motor?
I can fix this or do I have to send the warranty?
:/
I noticed that the front part of ta half “high” … does that this is normal or even bent upwards? Gee, what could cause this? a hit from the front? or a jump? : S
the picture can get a little confusing but this about 5mm taller tail end of “tray” for the chassis
